Believe it or not, but the error messages that you get from DrRacket occasionally contain useful information. (Okay, they always contain useful information. It may just be difficult to comprehend the information.) Read the messages. If they make sense, follow up on the error. If they don’t, check this reference or ask for help (or both).
Here are some of the more confusing error messages you might receive
and a possible explanation of those error messages. If you get other
error messages, please send them to
./../opt/racket/collects/mred/private/snipfile.rkt:324:2: open-input-file: cannot open input file path: /glimmer/lib/gigls/unsafe.rkt system error: No such file or directory; errno=2
Although we do our best to have gigls installed on every computer in MathLAN, some get missed (e.g., because they were off when we attempted to install gigls). Email the name of the computer to
and move to another computer.
../../usr/share/racket/collects/errortrace/errortrace-lib.rkt:399:2: load-extension: bad version 5.3.6@3m (not 5.2.1@3m) from "/glimmer/lib/louDBus/compiled/native/x86_64-linux/3m/loudbus.so"
We have two versions of DrRacket installed on the computers. This
message suggests that you are running the older version. Make sure
that your launcher is configured to use the newer version, which is
/opt/racket/bin/drracket. If you don’t know how to
configure your launcher, get help from a tutor, mentor, faculty
member, or perhaps even just an upper-level CS student.
(Instructions are in the Linux Lab
Chances are good that the MathLAN computer you are using tried to be helpful by remembering that you were running DrRacket the last time you logged out. Unfortunately, it re-launches the older (default) version of DrRacket when you log back in. It is highly likely that exiting DrRacket and restarting it using your panel launcher will solve the problem. (For one time anyhow; there’s no fix to the general problem of the machine trying to be helpful and failing.)
drawing-XXX: unbound identifier in module in: drawing-XXX
If the unbound identifier is one of the MediaScheme/gigls procedures,
you probably forgotten to include
in the top of the definitions pane. If the unbound identifier is not
one of those procedures, it just means that you forgot to define it.
(When we use
define to associate a name with a value,
Scheme says that the name (identifier) is “bound”.)
Can’t Render Drawings
. . ../../rebelsky/share/lib/gigls/drawings.rkt:1130:7: drawing-render!: Drawing does not fit within image bounds (image-width: 275 image-height: 184 drawing-left: 9453.0 drawing-top: 4231.875 drawing-right: 9591.0 drawing-bottom: 4324.375)
You will get an error message like this if you use
and the drawing you are using is outside the bounds of the of the
corresponding image. In this particular instance, since the image is
275 wide, the left edge of the drawing has to be smaller than 275.
It’s not. It’s 9453, which is much larger.
Not a procedure
application: not a procedure; expected a procedure that can be applied to arguments given: 3 arguments...:
This error message suggests that you have something other than a procedure immediately after an open parenthesis. (Many of us are tempted to parenthesize parameters and such. Scheme gets upset when you do that.)
This group of errors include the term
look something like the following.
. . gimp_drawable_get_pixel: call failed because GDBus.Error:org.gtk.GDBus.UnmappedGError.Quark._g_2dio_2derror_2dquark.Code13: call to gimp-drawable-get-pixel failed with an execution error
./../lib/gigls/tile.rkt:73:6: tile_stream_new: call failed because GDBus.Error:org.gtk.GDBus.UnmappedGError.Quark._g_2dio_2derror_2dquark.Code13: could not create stream
These errors usually indicate that something has gone wrong between GIMP and DrRacket. Save your work, quit both programs, restart both programs, and try again. If that fails, try contacting your instructor. Include your procedures, the input that seems to have led to the error, and anything else that might be of use.